Operational harmfulness of surface contamination with abrasive after the technological lapping process

Authors

  • Adam Barylski Gdansk University of Technology

DOI:

https://doi.org/10.24136/atest.2019.142

Keywords:

lapping, cast iron, contamination of surfaces, abrasive, analysis

Abstract

The methodology and results of qualitative and quantitative tests of surface contamination with abrasive micrograins and the influence of lapping conditions on the intensity of the phenomenon are presented. In the research, scanning microscopy and X-ray microanalysis were used.

Downloads

Download data is not yet available.

References

Barylski A., Obróbka powierzchni płaskich na docierarkach, Wy-dawnictwo Politechniki Gdańskiej, Gdańsk 2013.

Barylski A., Podstawy docierania jednotarczowego powierzchni płaskich, Wydawnictwo Politechniki Gdańskiej, Gdańsk 1992.

Barylski A., Skażenie powierzchni ścierniwem podczas docierania zagrożeniem dla eksploatacji maszyn. W: Konstytuowanie po-wierzchni materiałów, red. T. Zaborowski, IBEN, Gorzów Wlkp. 2018.

Bura S.T., Issedovanie šaržirovannych poverchnostej, obrabatannych almaznymi pastami, Brjanskij Institut Transportnogo Mašinostrojenja, Brjansk 1976.

Czichos H., Tribology: A Systems Approach to the Science and Technology of Friction, Lubrication and Wear, Elsevier, Amsterdam 1978.

Gates J.D., Two-body and three-body abrasion: a critical discussion, “Wear” 1998, vol. 214.

Galyko A.V., Juljugin V.K., Stecenko A.S., Ul’trazvukovaja očistka detalej asial’noporšnevych nasosov posle protirki, „Vest. Mašinostr.” 1973, nr 10.

Kremen’ Z.I., Pevzner R.L., Gavronskaja T.Ju.: Metody issledovanija šaržirovannoj poverchnosti dovodočnych pritirov, „Abrasivy” 1963, nr 6.

Leavers V.F., An active angularity factor for the characterization of abrasive particles, „Wear” 2000, vol. 239.

Malkin S., Guo C., Grinding Technology, Industrial Press, 2008.

Marinescu I.D., Hitchiner M., Uhlmann R., Rowe W.B., Inasaki I., Handbook of Machining with Grinding Wheels, CRC Press, 2007.

Marinescu I.D., Rowe W.B., Dimitrov B., Ohmori H., Tribology of Abrasive Machining Processes, Elsevier, Amsterdam 3013.

Marinescu I.D., Uhlmann E., Doi T.K., Handbook of lapping and polishing, CRC Press, Boca Raton, London, New York 2007.

Nepomnjaščij E.A., Kremen’ Z.I., Analiz processa šaržirovanija dovodočnych pritirov na osnove teorii slučajnych processov, „Vest. Mašinostr.” 1965, nr 9.

Rowe W.B., Principles of Modern Grinding Technology, Elsevier, Amsterdam 2009.

Spur G., Keramikbearbeitung. Schleifen, Honen, Läppen, Abtra-gen, Carl Hanser Verlag, München – Wien 1989.

Stachowiak D.W., Particle angularity and its relationship to abrasive and erosive wear, „Wear” 2000, vol. 241.

Trezona R.I., Allsopp D.N., Hutchings I.M., Transition between two-body and three-body abrasive wear: influence of the test conditions in the microscale abrasive wear test, “Wear” 1999, 205-214.

Ulegin V.G., Ogorodnikov A.P., Fizičeskaja suščnost’ šaržirovanija, „Almazy” 1973, nr 12.

Volkova T.M., Bura S.T., Dolgalenko A.P., Izmerenie glubiny vnedrenija i koliestvač vnedrivšichsja v poverchnost’ detali zeren pri obrabotke almaznym instrumentom, „Izmerit. Technika” 1970, nr 10.

Downloads

Published

2019-06-30

Issue

Section

Articles